$95.00
Add to cart

YHUBWLN3 YoctoHub Wireless-g

The YoctoHub-Wireless-g is a wireless-enabled module that can host three Yoctopuce modules to access them remotely through a Wifi network (802.11g). It can be powered either by a USB Micro-B cable and a regular phone charger, or a 5V battery pack.

The YoctoHub-Wireless-g can be used in the same way as a VirtualHub running on a little PC, but it is much easier to setup and maintain than a PC. It smaller and consume less. It is compatible out-of-the-box with all existing applications using Yoctopuce API. As for the VirtualHub, it can run autonomously using HTTP callbacks. The YoctoHub-Wireless-g can connect to a 802.11g wireless access point in infrastructure mode, but it can also work as a software access point (SoftAP) to provide wireless access to Yoctopuce modules from a mobile device without any additional infrastructure.

Moreover, the YoctoHub-Wireless-g features a built-in clock timer, that makes it possible to put the device into low-power deep sleep and wake-up automatically at predefined time. This makes it possible to reduce power consumption to 15uA while sleeping, which is crucial for applications running on battery or solar panels. The YoctoHub-Wireless-g only needs a few seconds of wake-up time to post data on an web server using the HTTP callback.

Three Yoctopuce modules can be connected directly, one of which can be fixed directly on the YoctoHub-Wireless-g and connected using a Board2Board-127 connector. More devices can be connected, thanks to the YoctoHub-Shield extension. The YoctoHub-Wireless-g can power Yoctopuce devices up to 2A.

The device is provided with an articulated antenna (9cm, with RP-SMA connector) and a connection cable (uFL to RP-SMA). The use of a real antenna makes it possible to connect to an access point from significantly farther than what most mobile phones and tablets can achieve.

Warning: although the 3 downstream ports hosting Yoctopuce devices use USB micro-B connectors, the YoctoHub-Wireless-g use a specific protocol simpler than USB to talk to the devices. Therefore, it is not possible to drive or even to power a regular (non-Yoctopuce) device using the YoctoHub-Wireless-g. It is not possible neither to use a regular USB hub (such as the Micro-USB-Hub) on the downstream ports. If you need more downstream ports for Yoctopuce devices, you can use a YoctoHub-Shield.

$124.12
Add to cart

YHUBWLN2 YoctoHub-Wireless-SR

The YoctoHub Wireless-SR is a wireless-enabled module that can host three Yoctopuce modules to access them remotely through a Wifi network. It can be powered either by a USB Micro-B cable and a regular phone charger, or a 5V battery pack.

The YoctoHub Wireless-SR can be used in the same way as a VirtualHub running on a little PC, but it is much easier to setup and maintain than a PC. It smaller and consume less. It is compatible out-of-the-box with all existing applications using Yoctopuce API. As for the VirtualHub, it can run autonomously using HTTP callbacks.

Moreover, the YoctoHub Wireless-SR features a built-in clock timer, that makes it possible to put the device into low-power deep sleep and wake-up automatically at predefined time. This makes it possible to reduce power consumption to 15uA while sleeping, which is crucial for applications running on battery or solar panels. The YoctoHub Wireless-SR only needs a few seconds of wake-up time to post data on an web server using the HTTP callback.

Three Yoctopuce modules can be connected directly, one of which can be fixed directly on the YoctoHub-Wireless-SR and connected using a Board2Board-127 connector. More devices can be connected thanks to the YoctoHub-Shield extension. The YoctoHub-Wireless-SR can power Yoctopuce devices up to 2A.

Contrarily to the YoctoHub-Wireless, which looks very similar, this version does not include an antenna connector but uses a tiny antenna directly integrated on the PCB. It takes less space, but should only be used in applications when there is a good wireless connectivity, away from any strong electromagnetic interference.

Warning: although the 3 downstream ports hosting Yoctopuce devices use USB micro-B connectors, the YoctoHub Wireless-SR use a specific protocol simpler than USB to talk to the devices. Therefore, it is not possible to drive or even to power a regular (non-Yoctopuce) device using the YoctoHub Wireless-SR. It is not possible neither to use a regular USB hub (such as the Micro-USB-Hub) on the downstream ports. If you need more downstream ports for Yoctopuce devices, you can use a YoctoHub-Shield.

$120.88
Add to cart

YHUBSHL1 YoctoHub-Shield

if you need to connect more Yoctopuce modules than allowed on our network hubs, you can add this extension board to them. Connected on the network hub with a picoflex ribbon cable (included), it will allow you to connect 4 additional Yoctopuce modules to the network. There is no need for a separate power supply cable, as the shield is powered directly through the picoflex ribbon cable.

The Yoctopuce modules can be connected to this shield using USB-OTG-MicroB-MicroB-20 cables, or using the more compact 1.27-1.27-11 cables (which require soldering). It is even possible to mount the devices directly on the shield (two on each side), and to connect them using Board2Board-127 connectors.

Warning: although the 4 downstream ports hosting Yoctopuce devices use USB micro-B connectors, the YoctoHub-Shield use a specific protocol simpler than USB to talk to the devices. Therefore, it is not possible to drive or even to power a regular (non-Yoctopuce) device using the YoctoHub-Shield. It is not possible neither to use a regular USB hub (such as the Micro-USB-Hub) on the downstream ports. However, if you need even more downstream ports for Yoctopuce devices, you can daisy-chain multiple YoctoHub-Shield.

$52.84
Add to cart

YHUBGSM4 YoctoHub-GSM-3G-NA

The YoctoHub-GSM-3G-NA is a wireless-enabled module that can host three Yoctopuce modules to access them remotely through a 3G GSM cellular network (UMTS and HSPA). It can be powered either by a USB Micro-B cable and a regular phone charger, or a 5V battery pack.

 

$248.40
Add to cart

YHUBGSM1 YoctoHub-GSM-2G

The YoctoHub-GSM-2G is a wireless-enabled module that can host three Yoctopuce modules to access them remotely through a 2G GSM cellular network (using GPRS EDGE, aka 2.75G). It can be powered either by a USB Micro-B cable and a regular phone charger, or a 5V battery pack.

 

$190.00
Add to cart

YHUBGSM3 YoctoHub-GSM-3G-EU

The YoctoHub GSM-3G-EU is a wireless-enabled module that can host three Yoctopuce modules to access them remotely through a 3G GSM cellular network (UMTS and HSPA). It can be powered either by a USB Micro-B cable and a regular phone charger, or a 5V battery pack.

 

$249.40
Add to cart

YHUBETH1 YoctoHub Ethernet

The YoctoHub Ethernet is a Fast-Ethernet module that can host three Yoctopuce modules to access them remotely. It can be powered either by a USB Micro-B cable, or directly from the Ethernet cable (PoE compatible with 802.3af standard).

The YoctoHub-Ethernet can be used in the same way as a VirtualHub running on a little PC, but it is much easier to setup and maintain than a PC. It smaller and consumes less. It is compatible out-of-the-box with all existing applications using Yoctopuce API. As for the VirtualHub, it can run autonomously using HTTP callbacks.

Three Yoctopuce modules can be connected directly, one of which can be fixed directly on the YoctoHub Ethernet and connected using a Board2Board-127 connector. More devices can be connected thanks to the YoctoHub Shield extension. The YoctoHub Ethernet can power Yoctopuce devices up to 2A.

Warning: although the 3 downstream ports hosting Yoctopuce devices use USB micro-B connectors, the YoctoHub-Ethernet use a specific protocol simpler than USB to talk to the devices. Therefore, it is not possible to drive or even to power a regular (non-Yoctopuce) device using the YoctoHub Ethernet. It is not possible neither to use a regular USB hub (such as the Micro-USB-Hub) on the downstream ports. If you need more downstream ports for Yoctopuce devices, you can use a YoctoHub Shield.

$121.88
Add to cart

MHUB0002 Micro-USB-Hub-v2

This device is a USB 2.0 hub . This is a multi-TT hub: it will perform better than a regular single-TT hub when several USB 1.1 devices are connected to it. It is tiny (42x28mm) and its size can even be cut down to 36x20mm, most probably one of the smallest you can find…

It is designed for DIY applications, for those who want to connect several USB devices in a tiny space. This hub does not have connectors for slave USB devices, but solder pads: you will be able to solder wires directly on it. Yoctopuce modules can be fixed on it using screws and spacers. This hub also supports external power supply, and will automatically switch from usb power to external power when available.

$32.78
Add to cart

THRMCPL1 Yocto Thermocouple Temperature Sensor

USB thermocouple sensor to measure the temperature at two points using thermocouples (types K, E, J, N, R, S and T supported). The module features a built-in datalogger. Two 50cm thermocouple fine wires are included.

$46.00
Add to cart

YVOCMK01 Yocto VOC Sensor

Tiny USB sensor to volatile organic compounds (VOCs) in ambiant air, with built-in datalogger

$116.10
Add to cart

VOLTAGE1 Yocto Volt

This tiny device is an isolated voltage sensor, for both AC and DC. It is electrically isolated, and includes a built-in data logger.

$59.70
Add to cart

Showing 1–12 of 56 results